Effects of Asian dust events on atmospheric bacterial communities at different distances downwind of the source region

Aeolian dust particles arising from arid and semiarid zones are known to carry microbes by air currents. The effect of wind-borne bacteria on atmospheric bacterial population at various downwind distances from the dust source regions must be clarified, but has not yet been reported. This study monitored the bacterial abundance and community composition in outdoor aerosol samples in Beijing, China, which is close to the Asian dust source regions, and compared them with the results obtained in a distant region(Osaka, Japan).The Asian dust collected in Beijing contained(4 ± 3) × 10~4 bacterial cells/m~3, approximately~4 times higher than in Osaka. On 15 April 2015, Beijing experienced severe Asian dust events with a 1000-fold increase in bacterial abundance, relative to non-Asian dust days. Dominant bacterial phyla and classes in Asian dust collected in Beijing were Actinobacteria, Bacilli and Acidobacteria, and the bacterial community composition varied more widely than in Osaka.The bacterial community compositions differed between the Beijing and Osaka dusts, even for the same Asian dust events. These results indicated that aerosol bacterial communities nearer the dust source are more affected by eolian dust than their distant counterparts.     

Submicron particle-bound polycyclic aromatic hydrocarbons in the Polish teaching rooms: Concentrations, origin and health hazard

The goal of the work was to investigate the concentrations of the 16 US EPA priority polycyclic aromatic hydrocarbons(PAH) bound to submicrometer particles(particulate matter, PM_1) suspended in the air of university teaching rooms and in the atmospheric air outside. Two teaching rooms were selected in two Polish cities, Gliwice, southern Poland,and Warsaw, central Poland, differing with regard to the ambient concentrations and major sources of PM and PAH. The variabilities of indoor and outdoor 24-hr concentrations of PM_1-bound PAH, the ratio(I/O) of the indoor to outdoor 24-hr concentrations of PM_1-bound PAH, probable sources of PAH and the level of the hazard from the mixture of the 16 PAH(ΣPAH) to humans at both sites were analyzed. In both Warsaw and Gliwice, the mean concentrations of PM_1-bound ΣPAH were slightly higher in the atmospheric air than in the rooms. The indoor and outdoor concentrations of individual PAH in Gliwice were correlated,in Warsaw – they were not. Most probably, the lack of the correlations in Warsaw was due to the existence of an unidentified indoor source of gaseous PAH enriching PM_1 in phenanthrene, fluorene, and pyrene. Although the ambient concentrations of PM_1-bound PAH were low compared to the ones observed earlier at both sites, they were much higher than in other urbanized European areas. However, because of low mass share of heavy PAH in ΣPAH, the various indicators of the health hazard from the 16 PAH mixture were low compared to other regions.     

宇宙尘星载原位探测技术研究

对宇宙尘探测的历史及主要探测技术进行了调研分析总结,介绍了电离型、压电型、电容型、电阻型、半导体型、质谱型等探测方法以及探测技术的发展,包括复合探测技术及大面积探测方法。基于我国宇宙尘探测技术所开展的研究工作还较少的现状,提出应在深空探测任务规划的基础上加快开展相关宇宙尘星载原位探测技术的研究储备,针对复合式探测技术及大面积探测方法等方面开展研究的建议。     

我国海洋塑料垃圾和微塑料排放现状及对策

当前海洋塑料和微塑料污染问题是全球研究热点,随着我国陆源垃圾减量化处置率和生活污水处理覆盖率的提高,重新核算我国海洋塑料垃圾和微塑料排放量尤为重要,基于文献已报道的关于海洋塑料垃圾和微塑料排放量估算的方法并结合相关统计数据对我国相应排放量进行了核算.结果表明:2016年我国向海洋中排放塑料垃圾124×104~331×104 t,略低于2010年的132×104~353×104 t;生活污水处理厂向环境中排放塑料微珠约109.95×1012粒（折合131.78 t）,远低于2014年报道的209.7×1012粒（折合306.9 t）.此外,2016年我国生活污水处理厂向环境中排放合成化学纤维类微塑料约1 296.95×1012个（折合648.48 t）,轮胎与地面摩擦产生合成橡胶轮胎粉尘约78.85×104 t;合成化纤类微塑料和合成橡胶轮胎粉尘等已成为陆源微塑料的重要来源.通过与发达国家和地区在海洋垃圾和微塑料污染、陆源垃圾处置、海洋垃圾污染应对等方面进行比较,未来我国应通过完善"限塑令"和生活垃圾分类体系、尽早实施"塑料微珠"限令、明晰生活污水处理厂微塑料排放状况等手段从源头控制排放,此外需有效控制塑料垃圾和微塑料的输送途径,制定和完善相关法律法规和监测标准,提升我国应对海洋塑料垃圾和微塑料污染的能力和国际影响力.      

水葫芦/污泥共热解法制备生物炭粒及其对Cr3+的吸附特性

为了促进水葫芦和污泥的资源化利用,探究水葫芦/污泥生物炭粒的基本理化性质及其对水中Cr3+的吸附机制,以水葫芦、污泥为原料,在300~500℃热解温度下制得生物炭粒,通过产率分析、灰分分析、比表面积和孔径分析及SEM（扫描电镜）分析,同时利用吸附动力学模型和等温吸附模型对生物炭粒吸附水中Cr3+的内在机制进行研究,最后采用TCLP（毒性浸出法）测定了不同生物炭粒中重金属的浸出毒性.结果表明:随着热解温度从300℃升至500℃,生物炭粒的产率从14.93%降至11.75%,生物炭粒的灰分含量逐渐升高,比表面积增大.SEM结果显示,水葫芦与污泥质量比为1:10时,生物炭粒比表面积较大,孔隙结构明显.当水葫芦与污泥质量比为1:10、热解温度为500℃时生物炭粒对Cr3+的吸附量最大,为44.96 mg/g.热力学分析显示,生物炭粒对溶液中Cr3+的吸附以化学吸附为主,且为单层吸附.TCLP试验表明,水葫芦/污泥生物炭粒中各重金属（Cd、Zn、Cu、Pb、Ni、Cr）的浸出浓度均低于GB 5085.3-2007《危险废物鉴别标准浸出毒性鉴别》的限值.研究显示,添加水葫芦能改善生物炭粒的理化性质,使得生物炭粒对Cr3+的吸附量增大,以化学吸附为主,且为单层吸附,水葫芦/污泥生物炭粒浸出毒性较低,可为生物炭类环境功能材料的研制提供选材依据.      

石家庄城市地表灰尘中多环芳烃的污染特征及来源

采用高效液相色谱法,对2017年2月12~19日所采集的石家庄市64个地表灰尘样品中16种优先控制的多环芳烃(PAHs)的含量和组分特征进行分析,并运用比值法和主成分因子载荷法揭示其污染来源。结果表明,16种PAHs的总量(Σ16PAHs)范围为0.897~81.458 mg/kg,平均值为8.138 mg/kg,其中Fla的含量最高为1.136 mg/kg,Flu最低为0.129 mg/kg,强致癌物质Bap为0.567 mg/kg。7种致癌多环芳烃(Σ7CPAHs)的含量范围为0.213~43.690 mg/kg,平均值为3.402 mg/kg,占Σ16PAHs的41.80%。与国内外其他城市相比,石家庄城市地表灰尘中PAHs含量处于较高水平,且以4环为主。来源分析结果表明,石家庄市地表灰尘中PAHs主要来源于化石燃料的燃烧,以石油燃烧为主,其方差贡献率为69.30%,柴油燃烧和石油泄漏的方差贡献率分别为8.67%和7.43%。由石家庄灰尘中PAHs的空间分布分析得出交通源对石家庄二环内冬季灰尘中PAHs贡献显著。     

抛光打磨车间便携式除尘器本体设计与试验

基于气旋分离和滤筒过滤的除尘原理,采用气旋分离作为一级除尘分离大颗粒粉尘,滤筒过滤作为二级除尘去除细颗粒物,设计并构建了适用于抛光打磨车间的便携式除尘器试验模型,并对其运行性能参数进行测试。结果表明：除尘器处理风量为117～179 m³/h,漏风率和设备阻力随处理风量的增加而升高,漏风率控制在3.52%以内,设备阻力最小为163 Pa,最大为393 Pa;除尘效率随风量的增大而发生轻微降低,该便携式除尘器的最高除尘效率达99.63%。     

酒精蒸气/烟草粉尘两相混合体系最小点火能试验研究

在烟草加工的加香工序,挥发的酒精和搅拌混料产生的烟草粉尘形成气粉混合体系,其燃爆特性相较于单相烟草粉尘有较大变化。对20 L爆炸球进行了部分改造,可完成20 ℃~80 ℃环境温度、100%LEL以下酒精蒸气浓度、最大2 J电火花能量组合的气粉混合物的最小点火能测试。选用烘丝和加香烟草粉尘做对比,探究了环境温度和酒精蒸气浓度对酒精蒸气/烟草粉尘两相混合体系点火能的影响规律。结果表明:相同环境温度下,加香烟草粉尘的最小点火能比烘丝烟草粉尘低;加香粉尘、烘丝粉尘及混合体系的最小点火能随环境温度变化的趋势一致,均随温度的升高而降低;加入10%LEL的酒精蒸气后,相同温度下气粉混合体系的最小点火能低于单相烟草粉尘。随着环境温度的升高,二者的差值逐渐减小,酒精蒸气诱导烟草粉尘最小点火能降低的能力逐步减小甚至消失;在电点火条件下,当酒精蒸气浓度低于50%LEL时,气粉混合体系较难被点燃,当酒精蒸气浓度高于75%LEL时,混合体系较易被点燃。     

基于凸形壁面的虚拟冲击式呼吸性粉尘采样器研究*

为研究满足BMRC曲线的呼吸尘采样器,提高呼吸尘采样的准确性,基于虚拟冲击原理,针对隔离主流和弱流通道壁面的形状,提出1种基于虚拟冲击原理的呼吸尘采样器的改进结构,并对不同模型进行模拟仿真实验,利用Ansys Fluent气-固2相流模拟采样器中的流场,对呼吸性粉尘颗粒在流场内的运动轨迹进行跟踪,对仿真得到的呼吸尘分离效能与BMRC曲线的标准进行对比。结果表明:相比采样器原型和主弱流壁面形状为“凹型”,虚拟冲击式呼吸尘采样器主弱流壁面形状为“凸型”时对呼吸尘采样的效果更好,同时分离效能与BMRC曲线的标准差为δ=2.65%,满足偏差小于等于5%的要求。研究结果可为呼吸尘采样器的优化设计提供参考。     

基于氧化还原分析的硫化矿尘爆炸压力预测*

为探究可应用于生产现场的硫化矿尘爆炸压力预测方法,基于硫化矿尘爆炸反应机理和粉尘引爆试验数据对硫化矿尘的氧化还原成分与其爆炸压力的相关关系进行分析。研究结果表明:硫化矿尘的还原成分指数与其爆炸压力的相关性极高,尤其是与其爆炸压力峰值的相关性系数高达0.993。整合研究结果形成的硫化矿尘爆炸压力和爆炸压力峰值计算和预测模型,可为金属矿山的硫化矿尘爆炸预防提供决策依据。